New homemade lures for jig spinning. Do-it-yourself catchy spinning tackle "Shnyryalka" Do-it-yourself summer spinning baits for a predator

Spinning fishing is one of the most popular types of fishing in almost all parts of the world. Spinning is caught on small rivers and large lakes, on the seas and even in the oceans. This publication is devoted to spinning and the features of spinning baits.

A little about the history of spinning

Spinning is called not only fishing tackle, but also the process of catching this type of rod with a reel. The ancestors of spinning are the British, and initially (and it was in the middle of the 19th century) casting spinning bait happened without help - then they were imperfect and at a high speed of ejection of the fishing line, it constantly got tangled. Therefore, the fishing line was removed from the reel and laid in rings on the ground. Casting was carried out manually, but a coil was already used for wiring.

The first mention of spinning fishing in Russia dates back to the 1880s - it was then in the magazine: "Nature and hunting." there was an article describing this type of fishing.

The process of choosing the necessary bait for spinning for many is in itself quite an exciting “sport”, and for some it is also a collectible. Since modern technologies have not bypassed the fishing industry, a variety of materials that do not always justify themselves have been used in the production of baits; plastics, PVC, adhesives, dyes, various metal alloys, etc. For collecting, such baits may be suitable, but at the expense of catchability and practicality, this is already a question.

In Soviet times, very few amateur fishermen caught on something other than standard metal lures, and only a select few knew what it was, because even the inertial Neva-150, which was scarce in many parts of the Union, was a rare success for many. Now everything looks different.

For many years, in spinning fishing, our domestic anglers have been using a wide variety of spinning lures, the most popular of which, perhaps, are the following types:

spinners;

silicone baits;

edible rubber.

Oscillating lures - the eternal classic of spinning fishing

are the largest species spinning lures- both in terms of the total number and the variety of options. This is one of the first, one might even say, ancient types of artificial lures, even spinners, which will be discussed below, appeared much later.

The fact that they are still used everywhere, better than any advertisement, says that this is still a fairly effective tool for spinning fishing. True, it is impossible not to notice that spinners are becoming more and more serious competition to them.
Structurally wavering bleu

sleep is usually metal spinning lure imitating the movement of a live fish. It is used for fishing on "artificial live bait" of predatory fish species, among which the most common are; pike, and trout. Despite the variety of shapes and sizes, spinners have a common structure and consist of a body, a hook and a mounting ring.
These baits for spinning differ both in material and type of coating, as well as in the method of manufacture.

Distinguish between copper, lead, steel and even plastic oscillating baubles. And they are produced by forging, stamping and casting.
The most common way to classify spinners is by dividing them according to the method of catching:

casting - the most common, for long-distance casting;

trolling - for fishing by towing;

non-catching "non-hooking" - used in heavily overgrown, difficult places;

fast sinking jig lures - for vertical lure.

Spinners - description and varieties

They have a widespread name - "turntables" - very popular. For most inexperienced anglers, revolvers are convenient because they do not require much experience or any special knowledge when catching them.

You can fish on a spinner in any weather, in open water and from the shore, in the current and without it. A classic spinner is a metal core that serves as a weight for the spinner, inside which a wire rod-basis of the spinner passes, part of the rod remains open for rotation of the petal on it, which is attached with a special clamp.

It can be made of any corrosion-resistant material or have a special coating. Both ends of the rod are twisted with a loop, on which, through the connecting rings and the swivel, a fishing line is attached on one side, and on the other tee hook. That's the whole simple construction.

During movement, the petal rotates around the spinner rod, creating vibrations in the water and reflecting reflections of light from itself, thereby attracting a predator. It is very remarkable that the turntables in no way, neither in appearance nor in the nature of movement, even closely resemble a live fish that can attract the attention of a predator, but despite this they are a huge success in amateur and sports spinning fishing.

Unlike oscillating lures, spinners are classified not by the method of catching, but by the method of loading; front loaded, back loaded And unloaded and in the form of a movable petal - "long" - long (elongated), "Comet" - comet (slightly rounded), "Aglia" - aglia (rounded and wider). The shape of the petal affects the angle at which to the axis, which is the wire rod, it rotates during movement.

For a more detailed description of the types and features of spinners with their classification, marking and other subtleties, read the article "Spinners". You will find a link to it at the bottom of the page - in "Related entries".

Wobblers are good bait for good fish

Wobblers- these are solid-state ones that are rapidly gaining popularity, which are used to catch predatory fish. Currently, wobblers are produced with different characteristics, having a wide range of penetration and buoyancy, suitable for use with any spinning fishing technique, both in still water and in current.

The main distinguishing feature of this bait lies in its very name "wobbler" from English is translated as "limping, staggering." The wobbler very successfully imitates a "limping" - wounded or sick fish, which is the easiest prey for a predator.

To date, the name "wobbler" includes a wide range of baits that are similar in appearance, but have different characteristics and differences in shape: poppers, walkers, cranks, fats, gliders, rattlins and others. They not only “limp and stagger”, but rattle, buzz, fly, jump on the water making different sounds, rotate their blades, in general, attract fish as best they can.

Many of the listed wobblers do not have their own “play”, and in order to achieve the maximum similarity of the bait with the behavior of a wounded fish, it is necessary to skillfully manipulate it. For these purposes, it is necessary to master the technique of the most accessible and common postings, having spinning at hand. (F) or ultra-fast - Extra-Fast (EF) and a good spinning reel.

The entire huge audience of wobblers, whose progenitor is James Heddon, who created the first wooden wobbler in 1894, is conditionally divided into types according to the degree of buoyancy: "floating"- floating, "suspend"- neutral buoyancy, "sinking"- sinking. Floating and sinking baits are usually classified according to the degree of buoyancy; "Slow"-slowly , "Fast"-fast.

Eg: "Slow sinking" - slowly sinking; "Fast sinking" sinking quickly. For baits with a special - pronounced degree of buoyancy, the term " Super" - super. Eg " Super Fast sinking"- very fast sinking or "Super Slowsinking " - sinking very slowly.

Wobbler classification with abbreviated symbols of their parameters and characteristics, marked on the body of the bait itself, is given in the article: "Classification and varieties of wobblers". You will find a link to the material at the end of the page - in the section: "Related posts".

Lures made of silicone and edible rubber

soft silicone lures- in the future, just lures, literally made a revolution in the fishing world of spinning players, deservedly gaining popularity among them, thanks to their many advantages. With the advent of silicone baits, spinning fishermen gradually began to forget about the home-made foam rubber fish popular in Soviet times, which are less and less used by amateur fishermen at the present time.

The variety of colors of artificial silicone baits made it possible to use them at any time of the day and in any weather. Not only predatory fish, but also peaceful inhabitants of reservoirs are tempted by their tempting color and appearance. Silicone twisters and vibrotails bite well even such peaceful fish as
This lure is used in various types of fishing. Miniature silicone artificial baits are used for catching peaceful fish; in a plumb line, on bottom gear, as well as in the usual float way.

So what is silicone bait and how is it different from edible rubber?
Baits made of silicone, like those of edible rubber, are made from the same material - silicone, with the only slight difference being that special flavors - attractants, flavors and salt are added to the edible rubber.
In fact, the same bait only with taste.

Some Chinese manufacturers, reducing production costs, use a cheap substitute, PVC, instead of high-quality silicone. Lures made of PVC are harder and less elastic, indicators - significantly worsening their catchability.

Artificial baits made of silicone are an imitation of fish, crustaceans, frogs and other inhabitants of the reservoir, which make up the main food supply for predatory fish. They are equipped with tees and doubles, as well as special jig heads, which are a monolithic hook design with a sinker located at its base.

Silicone bait in the process of wiring makes wave-like movements generated by the angler, rising to the surface and sinking to the bottom. The frequency and amplitude of which depends on the technique of wiring, and the speed of immersion on the weight jig heads and can be supplemented with jerks - tweet. Such wiring with jerks is called - "twitching" And "jigs". It is important that the bait does not sink to the bottom very quickly; for this, the jig head should not exceed the required weight.

Jig heads, eared sinkers and hooks

The main advantages of soft bait are its low price and, at the same time, excellent catchability, provided by the fact that predatory fish make several attacks on soft bait in one haul.

Soft - jelly-like bite bait, with a hardness not much different from the food object, does not alarm the fish during the first - unsuccessful or trial bite, and the predator continues to attack it again, thereby providing the fisherman with an additional chance to catch it. While the solid “taste” bait scares away the fish after the first unsuccessful bite.

The next significant advantage of soft bait is its ability to pass without hooks in the bottom layer of water overgrown with grass - there , where any other bait; wobbler, spinner or oscillator - will remain forever. This is achieved by the possibility of special installation of the offset hook into the soft body of the bait, so that the tip of the hook is protected from hooks as much as possible.

Silicone baits are divided into active - having a movable element that attracts the attention of fish, and inactive - sedentary, not having independently moving body parts capable of provoking a predator to attack .

Lures with jig heads

The most common active silicone baits are twisters and vibrotails. The tail part of these lures vibrates during movement, creating acoustic vibrations in the aquatic environment, which strongly attract fish. This quality, supplemented with different colors and flavors, if you take edible rubber, attracts predatory fish, and the correct animation with the bait provokes it to attack.

All other baits: worms, newts, frogs, squids, crustaceans, etc. are inactive baits that require certain manipulations with a rod and reel, using special hauling techniques, to closely resemble the behavior of a natural prey item.

The size of silicone baits is determined in inches - the minimum is 1 inch - 2.54 cm and is indicated on the package, the weight of the jig head is calculated in grams, often marked on the jig head itself.

The actions set forth in the article should not be taken as an axiom that does not require proof. You have to try everything yourself and conduct experiments, thanks to which new equipment and fishing accessories are born. Ingenuity is the engine of progress!

Best wishes! See you soon!

The spinning device is up to elementary simple, but at the same time quite effective in practical application. Few tackle in its monotonous structure can play the role of a tool for completely different types of fishing.

Having assembled a spinning rod, it can be used with equal success as a tool for catching predatory fish and as a tackle for bottom fishing, a match rod and an ordinary fly rod. In this diversity, it remains only to re-equip the spinning with rigs with nozzles for the next type of fish caught, but the main elements of the rod remain unchanged, universally fulfilling their obligations.

Any spinning tackle consists of the same set of accessories that give the rod the ability for practical use. The spinning equipment is as follows: the basis is the rod itself, consisting of a blank with throughput rings for fishing line and a handle with a mount for mounting the reel, the reel itself, the appearance of which may vary from the angler's preferences and fishing conditions.

The presented elements form the spinning tackle. Already in addition, the coil is endowed with a cord, but the equipment itself is attached directly to the cord. The equipment depends on the type of fishing and may consist of weights, floats, leashes with hooks, feeders, artificial lures and a combination of all these components. In the course of the article, we will consider the equipment in the section of each component, discuss its role in the general set of spinning equipment and discuss how all gear is prepared for fishing.

rod

Spinning is assembled on its basis, which is called a rod. Today, manufacturers make spinning tackle from the most modern ultra-light materials of artificial origin, which are distinguished by flexibility and elasticity, combined with high strength.

Most often, the blank is made of fiberglass, fiberglass, carbon fiber materials, and combinations of materials called composite. Depending on the type of material, a mass is formed at the form.

Important! A fiberglass rod is much heavier than a carbon fiber rod.

The rod can be made in two versions: a plug-in type and a telescopic assembly. The handle is made of a metal rod finished on its surface with natural cork or dense nylon. The choice of these handle finishes is characterized by the high ergonomic qualities of these materials.

The tactile sensations of the angler with such material do not cause even the slightest inconvenience, which does not distract the catching at all. On the handle of the fishing rod, a reel seat is built in with the principle of a threaded connection for attaching an accessory. Metal rings with line holders with composite or stainless steel liners, polished to the highest degree, are glued into the tackle blank. This condition is necessary to reduce the friction force arising from movement along the guide rings of the main cord.

Important! According to their performance, rods are divided according to their length, action or blank stiffness, test or power for loading tackle with bait or other type of equipment.

Spinningists, based on the characteristics of the stick, choose a certain type of fishing rod for the type of fishing.

Coil

The next fundamental element of what spinning consists of will be a reel. According to their types, fishing reels are divided into, multiplier and inertial. Devices are made of plastic and metal components. More acceptable options for fishing are reels in a metal case.

All presented types of mechanism have in their design features a uniformity in terms of legs, which has the ability to mate with a reel seat made on any gear. The general characteristics of the reels are their volume or line capacity and the presence of a braking device or friction clutch. Otherwise, inertialess and multiplier coils differ in the type of gear ratio, which is characterized by the number of rotations of the mechanism handle to the number of rotations of the rotor.

In relation to the rod, the reel is selected according to its overall dimensions and required characteristics for the conditions and type of fishing. Often, the manufacturer marks the product directly on its body, which is quite convenient when choosing an option for installation on a spinning tackle. Proper spinning equipment involves the installation of an inertia-free type of device. It is inertialess suitable for most types and conditions of fishing.

braided cord

Properly equipping a spinning rod without a braided cord is currently an almost impossible task. This type of line has firmly entered into fishing and especially spinning use because of its low stretch factor, which helps to effectively manipulate the bait and get a clear bite signal. Braided cords are classified according to their diameter and the number of veins twisted into a common cord. The greater the number of veins in the cord, the stronger and more reliable it is.

The diameter of the wattle fence varies from 0.06 to 0.5 mm. In addition, braids have a very rich color range, including soft muted tones and bright defiant colors. The diameter of the cord is selected based on the capabilities of the reel, the capacity of the spool and the possible size of the trophy caught. Thicker diameter braids are used for trolling fishing, the thinnest representatives of braided cords are the desired option for ultralight hunting.

Unlike monofilament lines, braids are distinguished, as already mentioned above, by low stretch, greater strength at smaller diameters and high abrasion resistance. Equipping a spinning rod with a braided cord is the most rational and convenient option for the angler.

Leashes

It is imperative to equip a spinning rod, especially for pike fishing, with a leash that will warn the angler against losing the nozzle. Spinning rigs include leads made of tungsten and titanium materials, and their fluorocarbon variations are also successfully used. Steel leashes are more rigid in relation to the above examples and are not entirely suitable for lure postings. Leashes, regardless of their material, are equipped with a swivel and a clasp, for the ability to equip the equipment with the necessary bait, without resorting to knitting and subsequent dressing when changing knots.

Important! The length of the leash is selected from the size of the fish expected in the catches. The larger the predator, the longer the leash should be.

Lures

A variety of artificial lures in today's realities indicates the high popularity of spinning fishing. I will list the main types of the most commonly used baits in this type of fishing hobby. Some of the most famous baits are all kinds. A wobbler is an imitation of a live fish or small animal, often a mouse or a frog, which is equipped with one or more hooks. Animating the bait in the water, the angler provokes the predator to attack.

Silicone baits in various versions repeat their shapes of fry, worms, insects, water beetles and larvae. Silicone is additionally equipped with a hook and a sinker, and only then is it introduced into the equipment used in the installation of spinning.

Spaced rigs, which include the Carolina and Texas rigs, deserved great love from spinning players. This direction of equipment involves the installation of the bait and its load separately from each other and sometimes at a considerable distance. Progressive equipment in the spinning movement is the application. By selecting a float according to its characteristics, weight and ability to stay on the surface or submerge in water, the angler manages to cast a small bait with a tackle for a considerable distance and carry out the wiring in the desired water horizon.

So, what is this spinning nod? As it turns out, this is a very interesting and useful addition to spinning, especially when fishing with jig and micro jig. For example, a spinning rod with a fast action and a test of 5-25 or 8-30g, being equipped with such a nod, can feel the wiring of lures weighing from 2-3g. That is, the range of baits used is greatly expanded, while not at the expense of the power of the tackle.

Spinning nods can be made in many ways. For this purpose, you can use: 1. Flexible tip from the feeder; 2. A piece of hard thick fishing line; 3. A strip of fiberglass from an old telescope; 4. A spiral twisted from a rigid fishing line; 5. Metal springs suitable in diameter and stiffness, etc.

If everything is simple with a nod from a feeder tip, a rigid fishing line and a metal spring, then it is worth dwelling on the remaining two types of spinning nods.

Fiberglass nod for jig spinning. Such a nod is made from a piece of knee from an old telescopic fishing rod. A chip 25-30 cm long and 2.5-3 mm wide is chipped from the blank. Edges and edges are processed with a file. It is important to sharpen well, round off the sharp edges of the future nod, otherwise cracks may appear there, which will eventually lead to breakage of the nod. The nod is painted with a “zebra” of white and red stripes or other combinations of colors (up to phosphorescent paints for night fishing). At the end, either a miniature “tulip” or a wire ring is installed, tied with a thread with sizing.

A fiberglass nod is attached to the top of the spinning rod with electrical tape or plaster. In fact, now it works as a particularly soft tip of a spinning rod, fixing touches of the bottom with the bait and the slightest bites.

More complex is a nod in the form of a spiral-spring, twisted from a thick fishing line or thermophyte monofilament. The end of the monofilament is fixed on the wire with a plaster and wrapped around the wire axis, turn to turn, very tightly. After winding 10-12 cm, the end is also fixed, and then the resulting spiral is drawn over the fire of the lighter evenly from all sides, but so as not to melt. In this way, the thermofit monofilament takes shape.

The excess ends of the fishing line are cut off and the edges of the nod are glued for reliability. A thermophyte tube is put on one end and heated, thereby clearly fixing it on the spring. Now you can color the nod with waterproof alcohol markers or nitro paints. In the working position, such a nod is inserted into the upper ring - the "tulip" of the spinning rod and is clamped with two pieces of cambric. The fishing line is passed inside the spiral spring. Thus, the nod clearly responds to the slightest changes in the position of the bait.

Personally, I prefer fiberglass spinning nods for their durability and relative ease of manufacture.

Floating boilies. Cooking at home

Fishing for carp with floating boilies is becoming more and more popular, proving its effectiveness. There is practically no reservoir where the fish is not familiar with this nozzle. Boilies are sold in almost all fishing stores. But, unlike their “colleagues” from the West, our anglers, who are used to saving money, are used to making their own nozzles and lures. And it's much more exciting to catch a carp on a bait prepared by one's own hands, when this cautious handsome man is not caught on store-bought boilies.
Catching carp on floating boilies is effective in silty waters. After all, no matter how fragrant the nozzle is, after a couple of hours, the silt interrupts all odors. A sinking boilie acquires a silty or rotten smell of pond vegetation.
Many will say that these are familiar smells for carp and this will not scare him away, but ... The task of the boilie in this case will not be completed. After all, the fish must be attracted with the help of flavors of the nozzle and tempted to bite. For this, odors are selected that cannot be interrupted by silt or aquatic vegetation.
At the moment, there are many recipes for making boilies at home. Some you can find on our website. But, almost all of them are for the preparation of sinking baits.
We, in order to keep the aroma as long as possible, need to prepare pop-up, that is, floating boilies. They are in the water column, not sinking into the silt, and retain their qualities longer, attracting and tempting carp to bite.

How to make floating boilies with your own hands?

The answer is simple, like everything ingenious: they should not be boiled, but cooked in the microwave.
The composition and ingredients remain the same, you can find them on our website. Then the boilies are not boiled in a saucepan, but are laid out in one layer on a shallow dish and placed in the microwave.
It must be remembered that the microwave flavors slightly worsens. Therefore, their number needs to be slightly increased in comparison with the usual recipe. Also, to increase buoyancy, you can add milk powder or casein, milk protein.
The most difficult thing in this operation is to choose the cooking time. Everything happens at the maximum temperature so that all the moisture from the nozzle evaporates and the time should be as long as possible, but burning of the boilies should be avoided.
After two minutes of cooking, you need to check the boilies for the presence of burning. Having examined the boilies and found no charring, you need to continue the process again, checking the bait every fifteen seconds.
As soon as signs of charring appear, we stop the process and note the time of the procedure and the diameter of the boilies for the future.
In order to check the correct preparation of floating boilies, you need to lower one ball into a container of water. If it starts to float, it means that you have cooked the boilies in the microwave correctly.
After all this, boilies can be soaked in oil, or dip or sweetener.
That's all. Now you know the cooking time and composition for the next portion.
Do it, experiment, be smart... After all, this is how new ideas, new ways of fishing appear!
No tail for you, no scales!

More articles about catching carp and carp:
Carp. Carp fishing.
Catching wild carp on boilies.
Catching big carp, carp. Adviсe.
When the carp does not peck.
Catching carp for corn.

See you on the pages of the articles of our website about fishing MirUlova.Ru and on our YouTube channel MirUlova.Ru - Fishing Video

DIY silicone bait making

Recently, silicone baits have become widespread, as the cheapest ones. There are several types of silicones:

Vibrotails. This silicone lure imitates the movement of fish in the water column. The design of the tail allows it to vibrate as it moves, hence the name.
Twisters. They are similar to a vibrotail, but the design of the tail allows the bait to work more actively.
Worms. They can have different lengths and thicknesses. This type of bait does not have its own game. Lures that imitate the movements of various animals, such as a frog, a mouse, a crayfish, etc., should be singled out in a separate row. This type of bait appeared quite recently.

To make silicone yourself, you must have:

Gypsum.
Lure samples.
Form to fill.
Silicone.

When heated, silicone softens to a state of fluidity. If there is a gas stove, then you can quickly melt it in some vessel.

When silicone appears on an open fire, you may encounter certain difficulties:

Silicone may burn.
Smokes when melted.
Can change its color.

To avoid such problems, silicone should be melted in the microwave. There it will not burn, and it will not change its original color.

In this case, it should be melted in such a way that it remains fluid for a long time. To do this, the silicone is still left in the microwave for a couple of minutes. After that, the vessel will warm up well, in which the silicone melts and its fluidity will be enough to fill the molds.

Gypsum is the material that will help make molds for pouring. Moreover, this does not require a lot of time and special skills. Gypsum is diluted with water to a creamy consistency, after which it is poured into a square mold made of plastic, wood or cardboard. After that, the bait is pressed into the plaster and left there until it solidifies completely. After about an hour and a half, you can pull out a sample from the plaster. As a result of mold manufacturing, the following problems are possible:

It can take a long time to make a mold due to the fact that it needs to dry well. If this is not done, bubbles may form during pouring, which will spoil the appearance of the silicone.
It is difficult to imprint small parts of the sample in plaster.
The finished form has low strength. If you overdo it, the form may burst.
After the silicone has cooled, the finished bait is difficult to get.

Such forms can be used to make simple shapes, such as worms and vibrotails, but to make a twister, problems arise here.

And here epoxy resin, which covers the finished form, can help. The layer should be very thin, and the mold dries well. The form coated with epoxy resin is devoid of all the above disadvantages. The baits are very easy to take out of it, while there are no traces of air bubbles. Naturally, the size of the bait will become somewhat smaller.

If you take too yellow and red colors, then you can achieve their perfect combination.

The step by step process consists of the following steps:

Melting silicone.
Pouring silicone into a mold.
Fill cooling.
Lowering the bait into cold water.

After cooling, the silicone must be immersed in cold water, as it may lose its plasticity and remain soft.

Methods for mounting silicone lures

Silicone baits are effective for jig fishing, so they are most often mounted using jig heads equipped with hooks. The size of the jig head is selected depending on the size of the bait, and its weight - depending on the depth of the reservoir and the presence of a current. The size of the hook should be optimal: a hook that is too large will prevent the bait from playing when retrieving, and a hook that is too small will increase the number of fish coming off. To keep the bait securely on the hook, you can fix it with super glue.

Many anglers equip their silicone baits with double hooks to keep the bait from slipping off the hook. As a rule, the hook is in the center of the lure. To install the hook on the bait, you need to visually determine the exit point of the hook sting, after which a puncture is made in the center of the body of the bait, followed by pulling the hook through the puncture site. After the sting comes out, the bait should rest against the eye of the hook, or against the jig head. If the hook is not attached correctly, then the bait will begin to hang on it, which is not very good, since it will often have to be corrected, and it will play improbably.

It is possible, as a rigid attachment of the bait to the jig head, as well as a movable one, when the hook and the load are connected through a flexible connection, such as a winding ring. The flexible connection enables more active and believable play. Sometimes such a connection is more effective and more efficient.

Silicone lures are also equipped with offset hooks. Offset hooks can be:

Curved, oblong shape.
Direct form.

Offsetters with a straight shape are used quite rarely and only for worm-shaped lures. In most cases, curved offsets are used. To equip the bait with an offset, everything should be clearly calculated so that the bait is not too tight and does not hang out. To do this, apply the bait to the offset and mark the place of punctures, both in front of the bait and in the center. First, the bait is pierced in front and the sting of the hook is immediately removed, after which a puncture is made with this sting at another point. The sting is removed from the back of the bait. On sale you can find silicones, in which there are ready-made slots on the back of the bait, in which the tip of the hook is hidden.

Some anglers manage to install tees on silicone lures. This is a complex technology and without certain skills this should not be done, as you can ruin the bait. The same is true for mounting doubles (double hooks). Naturally, these hooks reduce the number of hooks, but in order to install them, you need to see with your own eyes how it is done, then try it on some unnecessary bait, and only then practice at home.

Given the fact that you can make silicone baits yourself, they are the cheapest. You can also collect other types of baits at home, including oscillating and spinning lures, as well as wobblers, but this requires special skills. In addition, such baits are difficult to paint in the desired colors. Sometimes this requires the skills of an artist. Making silicones is much easier and only requires colored silicone and a mold. Having made one form, you can provide yourself with silicone baits for the whole season. The presence of several forms will provide silicones of various types. In this case, they will cost a penny.

Video tutorials on installation

Do-it-yourself water cannon for a boat

How to make a hinged transom for a PVC boat? ...

Homemade fishing rod stand

Do-it-yourself nod for a winter fishing rod

Do-it-yourself winter spinners for perch

Do-it-yourself snowmobile for fishing

Do-it-yourself self-cutting winter fishing rod ...

DIY fishing boat

DIY spinner making